702 & 802 Aermotor Windmill Parts Price List
Authentic Aermotor Windmill Repair Parts
*Prices subject to change without notice, July 2008.
ll prices for shipment or pickup only. Installation prices are full retail.
 |
The 702 Model Windmill by T. Lindsay Baker. A must if you want to repair an Aermotor windmill.$29.95 plus tax (if applicable) |
I. Complete 802 Aermotor Mill only (no tower)
| 6 ft. | 8 ft. | 10 ft. | 12 ft. | 14 ft. | 16 ft. |
| $2,520.00 | $2,615.00 | $3,750.00 | $6,205.00 | $8,860.00 | $11,650.00 |
II. Aermotor Windmill 4 Posts Steel Tower w/wood platforms and stub
Galvanized Steel Platfroms also available for extra cost . See below for prices.
| Tower Height (ft) | 6ft or 8ft | 10ft | 12ft | 14ft | 16ft |
| 21 | $1,896.00 | $2,180.00 | |||
| 27 | $2,320.00 | $2,960.00 | $3,510.00 | $3,570.00 | |
| 33 | $2,720.00 | $3,160.00 | $3,730.00 | $4,180.00 | $5,394.00 |
| 40 | $3,320.00 | $3,720.00 | $4,380.00 | $4,580.00 | $6,330.00 |
| 47 | $3,780.00 | $4,380.00 | $5,140.00 | $6,480.00 | $7,830.00 |
III. 702 & 802 Aermotor Components (1933-Present)
#32 Vane Assembly: Vain w/bolts to attach to tail bone
| 6 ft. | 8 ft. | 10 ft. | 12 ft. | 14 ft. | 16 ft. |
| $215.00 | $265.00 | $345.00 | $535.00 | $695.00 | $1,050.00 |
664 1/2 Pipe Base Assembly: Mast pipe w/Furl lever #609S
| 6 ft. | 8 ft. | 10 ft. | 12 ft. | 14 ft. | 16 ft. |
| $295.00 | $345.00 | $445.00 | $549.00 | $1,055.00 | $1,349.00 |
#747 Tail Assembly: Tail bone #639 w/Pivot bolt #510 and spring #28
| 6 ft. | 8 ft. | 10 ft. | 12 ft. | 14 ft. | 16 ft. |
| $210.00 | $264.00 | $365.00 | $595.00 | $945.00 | $1,188.00 |
#799 Wheel Assembly: Complete wheel w/arms #736, sails #100, sail ribs #101, inner and outer bands #34, #35
| 6 ft. | 8 ft. | 10 ft. | 12 ft. | 14 ft. | 16 ft. |
| $585.00 | $715.00 | $1,320.00 | $2,100.00 | $3,200.00 | $4,450.00 |
#881 Crated Motor: main frame w/gears, hub, hood by Aermotor
| 6 ft. | 8 ft. | 10 ft. | 12 ft. | 14 ft. | 16 ft. |
| $1,615.00 | $1,730.00 | $2,440.00 | $3,660.00 | $4,790.00 | $6,380.00 |
IV. 702 & 802 Aermotor Component Repair
#875 Basic Motor by Aermotor
| 6 ft. | 8 ft. | 10 ft. | 12 ft. | 14 ft. | 16 ft. |
| $1,396.00 | $1,498.00 | $2,132.00 | $3,478.00 | $4,550.00 | $5,650.00 |
Bearings for 802 Pitman Arms
| 6 ft. | 8 ft. | 10 ft. | 12 ft. | 14 ft. | 16 ft. |
| $14.00 | $19.00 | $33.00 | $38.00 | $51.00 | $66.00 |
Box bolts for #799 wheel assembly
| 6 ft. | 8 ft. | 10 ft. | 12 ft. | 14 ft. | 16 ft. |
| $31.00 | $37.00 | $52.00 | $73.00 | $86.00 | $115.00 |
Tools: Taps for Aermotor Hubs
| 6 ft. | 8 ft. | 10 ft. | 12 ft. | 14 ft. | 16 ft. |
| $52.00 | $58.00 | $70.00 | $145.00 | $145.00 | $168.00 |
V. 702 & 802 Aermotor Replacement Parts (1933-Present)
Please call for parts not listed.
| Part Number | Item | 6ft (X) | 8ft (A) | 10ft (B) | 12FT (B) | 14ft (D) | 16ft (F) |
| 28 | Vane Spring | 18.00 | 23.00 | 43.00 | 75.00 | 125.00 | 170.00 |
| 31 | Vane less #44 and #46 | 196.00 | 250.00 | 325.00 | 715.00 | 665.00 | 985.00 |
| 34 | Outer Band of Wheel | 22.00 | 30.00 | 63.00 | 92.00 | 182.00 | 240.00 |
| 35 | Inner Band of Wheel | 10.00 | 19.00 | 29.00 | 50.00 | 68.00 | 103.00 |
| 44 | Marrow U-Bolt w/Hardware | 10.00 | 12.00 | 12.00 | 15.00 | 17.00 | 27.00 |
| 46 | Wide U-Bolt Hardware | 10.00 | 12.00 | 12.00 | 17.00 | 24.00 | 39.00 |
| 62 | Connection-Pump Poll/Well Rod | 22.00 | 22.00 | 28.00 | 37.00 | 52.00 | 82.00 |
| 100* | Sail/Complete w/sail tie | 26.00 | 33.00 | 59.00 | 77.00 | 105.00 | 145.00 |
| 101 | Sail Rib | 6.00 | 8.00 | 11.00 | 15.00 | 19.00 | 28.00 |
| 171 | Pump Rod Complete | 52.00 | 55.00 | 75.00 | 130.00 | 235.00 | 385.00 |
| 243 ½ | Furl Handle Assembly w/#334 | 41.00 | 41.00 | 58.00 | 81.00 | 87.00 | 129.00 |
| 334 | V-Bolt for Furl handle Mount | 8.00 | 9.00 | 11.00 | 13.00 | 15.00 | 15.00 |
| 507 | Oil Ring | 8.00 | 9.00 | 10.00 | 13.00 | 14.00 | 16.00 |
| 508 | Pitman Guide Complete need w/588, (2) 588R | 41.00 | 49.00 | 63.00 | 140.00 | 255.00 | 290.00 |
| 508R | Pitman Guide Rivet | 1.00 | 2.00 | 3.00 | 4.00 | 5.00 | 6.00 |
| 510 | Pivot Bolt for Tailbone | 20.00 | 23.00 | 37.00 | 57.00 | 80.00 | 115.00 |
| 517 | Spring for Spout Washer | 3.00 | 3.00 | 5.00 | 6.00 | 7.00 | 8.00 |
| 520 | Oil Collector | 11.00 | 12.00 | 14.00 | 16.00 | 25.00 | 35.00 |
| 521 | Split Washer | 9.00 | 10.00 | 12.00 | 14.00 | 18.00 | 21.00 |
| 522 | Shaft for Guide Wheel & Yoke | 13.00 | 20.00 | 28.00 | 38.00 | 72.00 | 106.00 |
| 523 | Guide Wheel | 29.00 | 35.00 | 45.00 | 75.00 | 106.00 | 150.00 |
| 527 | Furl Link w/cotter pin | 8.00 | 9.00 | 14.00 | 16.00 | 22.00 | 27.00 |
| 528 | Furl Arms w/cotter key (pair) | 23.00 | 30.00 | 36.00 | 59.00 | 69.00 | 85.00 |
| 528 ½ | Furl Arms Long for Repair (pair) | 24.00 | 31.00 | 38.00 | 61.00 | 72.00 | 89.00 |
| 528 ¾ | Furl Arms Extra Long for Repair (pair) | na | 33.00 | 40.00 | 63.00 | 74.00 | 93.00 |
| 560 | Hood | 154.00 | 168.00 | 194.00 | 262.00 | 435.00 | 495.00 |
| 565 | Nut for 588 | 4.00 | 4.00 | 4.00 | 5.00 | 5.00 | 6.00 |
| 576 | Steel Washer for Turntable | 1.00 | 3.00 | 4.00 | 6.00 | 7.00 | 8.00 |
| 578 | Locknut for Top of Mastpipe | 9.00 | 14.00 | 22.00 | 32.00 | 44.00 | 51.00 |
| 579 | Lockwasher for Top of Mastpipe | 4.00 | 4.00 | 6.00 | 7.00 | 8.00 | 10.00 |
| 580 | Vane Spring Holder | 9.00 | 13.00 | 16.00 | 29.00 | 32.00 | 36.00 |
| 585 | Tailbone Casting | 35.00 | 42.00 | 74.00 | 87.00 | 117.00 | 145.00 |
| 588 | Stud for Pittman Guide | 5.00 | 5.00 | 5.00 | 8.00 | 9.00 | 11.00 |
| 608 | Pump Rod Yoke | 48.00 | 52.00 | 66.00 | 105.00 | 150.00 | 225.00 |
| 609S | Furl Lever Complete 4-Post Tower | 88.00 | 107.00 | 150.00 | 203.00 | 325.00 | 400.00 |
| 610 | Pin for Yoke | 5.00 | 6.00 | 8.00 | 9.00 | 11.00 | 15.00 |
| 613 ½ | Upper Furl Ring w/Wear Ring, w/o Arms | 73.00 | 74.00 | 90.00 | 135.00 | 200.00 | 290.00 |
| 614S | Lower Furl Ring 4 Post Split | 35.00 | 38.00 | 57.00 | 74.00 | 90.00 | 110.00 |
| 622 | Bolt | 5.00 | 6.00 | 8.00 | 11.00 | 13.00 | 14.00 |
| 639 | Tailbone Assembly w/#510 | 102.00 | 134.00 | 215.00 | 355.00 | 635.00 | 699.00 |
| 659 | Buffer Device Complete | 69.00 | 76.00 | 138.00 | 165.00 | 235.00 | 305.00 |
| 661 ½ | Pipe and Base Assembly | 240.00 | 264.00 | 335.00 | 470.00 | 810.00 | 1070.00 |
| 674 | Pipe Base Only 4 Post | 62.00 | 62.00 | 82.00 | 114.00 | 185.00 | 262.00 |
| 686 | Pitman Arm | 31.00 | 38.00 | 86.00 | 98.00 | 190.00 | 255.00 |
| 690 | Brake Band | 27.00 | 36.00 | 49.00 | 74.00 | 123.00 | 159.00 |
| 703 | Hub and Shaft Assembly w/729 and 744 | 320.00 | 330.00 | 420.00 | 855.00 | 1270.00 | 1700.00 |
| 704 | Pinion Gear | 49.00 | 57.00 | 92.00 | 122.00 | 161.00 | 241.00 |
| 705 | Large Gear | 135.00 | 146.00 | 235.00 | 399.00 | 395.00 | 590.00 |
| 708 | Pinion Gear Bearing Babbit | 28.00 | 40.00 | 73.00 | 112.00 | 148.00 | 240.00 |
| 711 | Oil Socket for 520 (model 702) | 7.00 | 8.00 | 10.00 | 16.00 | 23.00 | 24.00 |
| 718 | Spout Washer | 12.00 | 14.00 | 16.00 | 22.00 | 32.00 | 37.00 |
| 720 | Shaft for 702 w/(2) 721 pins | 15.00 | 25.00 | 46.00 | 63.00 | 99.00 | 155.00 |
| 721 | Pin for 720 Shaft | 3.00 | 4.00 | 5.00 | 8.00 | 9.00 | 10.00 |
| 729 | Pin for Hub Shaft | 2.00 | 3.00 | 4.00 | 5.00 | 6.00 | 7.00 |
| 730 | Sleeve Bearing (babbit) | 43.00 | 64.00 | 107.00 | 140.00 | 245.00 | 365.00 |
| 736 | Wheel Arm w/nuts and washers | 24.00 | 32.00 | 38.00 | 52.00 | 97.00 | 121.00 |
| 744 | Key for 704 | 4.00 | 6.00 | 8.00 | 14.00 | 16.00 | 18.00 |
| 751 | Bearing Bar | 12.00 | 19.00 | 22.00 | 31.00 | 51.00 | 76.00 |
| 752 | Bearing for Large Gear (babbit) | 43.00 | 60.00 | 94.00 | 156.00 | 230.00 | 285.00 |
| 755 | Large Gear Assy. (babbit) need w/(2)-705, 720, 752 | 325.00 | 335.00 | 595.00 | 999.00 | 1,210.00 | 1,575.00 |
| 781 | Countersunk Plug | 4.00 | 4.00 | 5.00 | 8.00 | 10.00 | 10.00 |
| 786 | Brake Lever | 30.00 | 35.00 | 55.00 | 75.00 | 134.00 | 167.00 |
| 802 | Main Frame | 718.00 | 795.00 | 1,050.00 | 1,850.00 | 3,150.00 | 4,499.00 |
| 806 | Key, Pinion Gear | 5.00 | 6.00 | 6.00 | 15.00 | 16.00 | 17.00 |
| 808 | Pinion Gear Brg. (Garlock w/806 key); fits 702 | 39.00 | 53.00 | 75.00 | 155.00 | 199.00 | 285.00 |
| 830 | Sleeve Bearing (Garlock) | 105.00 | 119.00 | 190.00 | 235.00 | 340.00 | 785.00 |
| 852 | Bearing for Large Gear (Garlock) | 46.00 | 70.00 | 95.00 | 165.00 | 225.00 | 280.00 |
| 855 | Lrg. Gear Assy. need w/(2)-705A, (1)-720, (1)-852 | 335.00 | 385.00 | 615.00 | 1,035.00 | 1,210.00 | 1,640.00 |
VI. 702 & 802 Aermotor 4 Posts Tower Platforms
*Oversized Galvanized steel platforms also available.
| Mill Size | Standard Platform (wood / steel) | Price (wood / steel) | Oiling Platform | Price (wood / steel) |
| 6ft or 8ft | T-149 / 149G | $168.00 / $315.00 | ||
| 10ft | T-151/ 151G | $179.00 / $346.00 | ||
| 12ft | T-249 / 249G | $184.00 / $382.00 | T-249 ½ | $115.00 / $230.00 |
| 14ft | T-279 / 279G | $200.00 / $430.00 | T-279 ½ | $115.00 / $230.00 |
| 16ft | T-749 | $454.00/$486.00 | T-383 | $115.00 / $230.00 |
VII. 702 & 802
Aermotor Windmill 4 Post Steel Stub Towers w/appropriate wood platform(s)
*Steel platforms optional
| Stub Height (ft) | 6ft or 8ft | 10ft | 12ft | 14ft | 16ft |
| 3ft (no platform) | $188.00 | $220.00 | |||
| 4ft | $385.00 | $405.00 | $420.00 | ||
| 5ft | $460.00 | ||||
| 7ft | $499.00 | $535.00 | $745.00 | $795.00 | $1,195.00 |
| 14ft | $1,225.00 |
MONITOR Brand Hand Pumps
These are the Old Style Hand Pumps with a lever.
11HA For Shallow wells less than 80ft, $625.00
11HB For Deep Wells less than 200 ft, $668.00
